Installation, Operation and Service Manual Following installation, please forward this manual to the appropriate operations person.208596R0725CT400A/W
5. If power is to be supplied through counter cut-out, complete steps 6-9. If power is to be supplied through rear of dispenser, proceed to step 10
Installing wall mount dispensers 1. Install supplied wall bracket with six 3/8" diameter fasteners as shown in Fig. 7. Note: Three holes are a
8. Remove utility knock-out (Fig.4, 5F) from rear of dispenser and install supplied protective grommet. For dispensers using remote icemakers, remo
Installing Satellite-fill icemakers Models 25CR400A/W, 50CR400A/W, 25HR400A/W, 50HR400A/W 1. Install Satellite-fill icemaker following instructions
1. On dispensers equipped with top-mounted, water-cooled icemakers, feed condenser supply and drain lines from back through utility knock-out (Fig.
15ice level control stat45.75"(19mm)Hand bend cap tubeend to approx. 45as shownFig. 11 – Ice transport tube and ice level control stat mounting u
User informationHow the dispenser worksFollett’s 25 and 50 automatic load ice and water dispensers receive ice from Follett’s 400 lb (181kg)/day icema
If dispenser is a SensorSAFE unit: 3. Deactivate dispenser by depressing and releasing clean switch located on left side of unit under top front co
bin signalpurplebluepurpleredswitcht-statdispenser powerswitchwhitewhitewhitewhiteredice machinebin signal(120 VAC)MWTRlocated behind splash panel4x4
How unit works — SensorSAFE modelsSensorSAFE models provide “touchless” ice and water dispensing. When a container is placed within the actuation zone
Before you beginSpecifications Field wiringInstallation Installing freestanding dispensers Installing countertop dispensers Installing wall mount d
20Dispenser troubleshootingBefore calling for service:• Check that there is ice in dispenser bin area • Check that all switches and circuit breaker
ActionCheck LEDs on control boardPlace cup under drop zoneLED Status PWR CLN ICE/WTR OFF OFF OFF ON ON OFF ON OFF OFF ON OFF ONSolutionCheck
22Lens/sensor troubleshooting 1. Turn dispenser power switch off. 2. Remove splash panel. 3. Disconnect wires from output terminal(s) (WTR, WM) o
Ice transport tube replacement Models 25CT400A/W, 25HT400A/W, 50CT400A/W, 50HT400A/W Only use tubing supplied by Follett Corporation.!Disassembly and
Ice transport tube replacement Models 25FB400A/W, 50FB400A/W, 25CR400A/W, 50CR400A/W 1. Remove top and rear access panel from dispenser (lower fron
well nutice levelcontrol statrubber grommetcontrol box assemblyice mounting hose bracketknurled screwhopper assemblyice level control statbin thermost
Part # Description Reference502679 Cover, top front, 25 countertop (CT) & wall mount (HT) units 1502680 Cover, top front, 50 countertop (CT)
Part # Description Reference502057 Fastener, dispense chute bracket 1502356 Tube, water station 2502681 Cover, dispense chute 3502359 Switch,
28Part # Description Reference502057 Fastener, dispense chute bracket 1502681 Cover, dispense chute (includes labels) 2502689 Chute and funnel,
Part # Description Reference501861 Wheel motor, 120V, 60Hz 1501026 Washer, thrust 2501607 Fan blade, wheel motor Not shown501619 Drive shaft (
Welcome to FollettFollett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale
30Part # Description Reference501608 Baffle, ice 1501614 Wheel, dispense (includes drive bar, rotating agitator, threaded bar & rod) 2502821
31Part # Description Reference502598 Coil, chilled water (includes two 502599) 1502599 Fitting, water coil 2502600 Brackets, chilled water cani
208596R0704/07801 Church Lane • Easton, PA 18040, USAToll free (800) 523-9361 • (610) 252-7301Fax (610) 250-0696 • www.follettice.comCountertop dispen
4SpecificationsElectrical1. Models with Satellite-fill icemakers (25CR400A/W, 50CR400A/W, 25HR400A/W, 50HR400A/W) Icemaker Max. fuse Dispe
Attention – Should local codes require a hard-wired connection and/or shielded wiring, eliminate the cord and plug(s) and follow the appropriate field
6Field Wiring diagrams(For installations requiring hard-wiring equipment)Freestanding dispensers, countertop and wall mount dispensers with integral i
Installation procedureInstalling freestanding dispensers 1. Carefully tip dispenser back to expose underside and block up in place. 2. Remove le
12 Verify that water sensor tabs are immersed in water in reservoir. 13. Remove top front cover by removing two screws at bottom corners of cover.
Installing countertop dispensers 1. Position dispenser in desired location, mark dispenser outline on counter and removedispenser. 2. Drill four 3
Comments to this Manuals